Gel coat is the outer layer of fiberglass. Its structural value is not significant. However, it gives the product its shine and color. In addition, it offers protection to the hull. Read on to know more on how to restore faded fiberglass.
Exposure and time usually erode the outer layer. This makes the item look chalky and dull. However, you do not have to worry about this because it is a problem which can be fixed easily. The initial phase is to clean the product. Lukewarm water is preferred. If possible, use some detergent and a sponge. Nevertheless, you ought to don on some gloves to protect your hands.
Mildew can cause a lot of damage. However, it is not easy to eliminate it. Thus, you should pour some bleach on it. The stubborn stains can be done away with by directly applying the concentrated cleaner on them. Careful rinsing is emphasized to remove all traces of the cleaning detergent. The surface should be dried afterwards.
Ensure there are no traces of oil before proceeding. Cleaning alone cannot guarantee this. That is why you need to get more serious oil removers. They include acetone and MEK. Make sure there are several cotton cloths to use in removing the oil. After accomplishing this you can wax the fiberglass. This is an essential step which helps in prolonging the life of the product.
The procedure of applying wax differs depending on the manufacturer. Therefore, you have to read the instructions given. Nevertheless, a foam pad or cloth is used in applying the wax. Proceed in circular motions. After the wax has dried, you should buff the excess using a soft piece of cloth.
Polishing follows waxing. Abrasives are needed for this task. Fine sandpaper is recommended. All pitted spots will be made smooth. Coating alone cannot achieve this. Dividing the surface in sections and tackling each at a time is advisable. Ensure you move in circles all the time. You ought to only stop when you can see your own image on the particular surface. Remember to apply a fresh coat of wax afterwards. Some polish preparations have wax.
If the surface has been eroded extensively, you should get a better abrasive. Before applying fresh wax, you ought to do away with the old one. If you ignore this, the particular surface will not be even. Straight strokes are preferred. There are several solutions that can be utilized for this process. However, toluene is more common.
A restorer should be applied last. There are a lot of them meaning you will not have a difficult time shopping for one. They work almost the same as wax. Nonetheless, buffing is recommended after the restorer has being applied. You will be impressed with the results. However, remember that the item will not retain the new look forever. However, it will last for some time if you take care of it well.
Exposure and time usually erode the outer layer. This makes the item look chalky and dull. However, you do not have to worry about this because it is a problem which can be fixed easily. The initial phase is to clean the product. Lukewarm water is preferred. If possible, use some detergent and a sponge. Nevertheless, you ought to don on some gloves to protect your hands.
Mildew can cause a lot of damage. However, it is not easy to eliminate it. Thus, you should pour some bleach on it. The stubborn stains can be done away with by directly applying the concentrated cleaner on them. Careful rinsing is emphasized to remove all traces of the cleaning detergent. The surface should be dried afterwards.
Ensure there are no traces of oil before proceeding. Cleaning alone cannot guarantee this. That is why you need to get more serious oil removers. They include acetone and MEK. Make sure there are several cotton cloths to use in removing the oil. After accomplishing this you can wax the fiberglass. This is an essential step which helps in prolonging the life of the product.
The procedure of applying wax differs depending on the manufacturer. Therefore, you have to read the instructions given. Nevertheless, a foam pad or cloth is used in applying the wax. Proceed in circular motions. After the wax has dried, you should buff the excess using a soft piece of cloth.
Polishing follows waxing. Abrasives are needed for this task. Fine sandpaper is recommended. All pitted spots will be made smooth. Coating alone cannot achieve this. Dividing the surface in sections and tackling each at a time is advisable. Ensure you move in circles all the time. You ought to only stop when you can see your own image on the particular surface. Remember to apply a fresh coat of wax afterwards. Some polish preparations have wax.
If the surface has been eroded extensively, you should get a better abrasive. Before applying fresh wax, you ought to do away with the old one. If you ignore this, the particular surface will not be even. Straight strokes are preferred. There are several solutions that can be utilized for this process. However, toluene is more common.
A restorer should be applied last. There are a lot of them meaning you will not have a difficult time shopping for one. They work almost the same as wax. Nonetheless, buffing is recommended after the restorer has being applied. You will be impressed with the results. However, remember that the item will not retain the new look forever. However, it will last for some time if you take care of it well.
About the Author:
You can visit www.leprechaunmagic.com for more helpful information about Concerning How To Restore Faded Fiberglass.